Hiển thị các bài đăng có nhãn GALVALUME. Hiển thị tất cả bài đăng
Hiển thị các bài đăng có nhãn GALVALUME. Hiển thị tất cả bài đăng

Thứ Sáu, 2 tháng 10, 2015

ANTI-DUMPING Steel Reinforcing Bar Australian

Steel Reinforcing Bar

Exported from the Republic of Korea, Malaysia,

Singapore, Spain, Taiwan, the Kingdom of Thailand and the Republic of Turkey

Preliminary Affirmative Determination and

Imposition of Securities

Customs Act 1901– Part XVB
On 17 October 2014, I, Dale Seymour, the Commissioner of the Anti-Dumping Commission (the Commission),nitiated an investigation into the alleged dumping of steel reinforcing bar (rebar) exported to Australia from the Republic of Korea (Korea), Malaysia, Singapore, Spain, Taiwan, the Kingdom of Thailand
(Thailand) and the Republic of Turkey (Turkey), following an application lodged by OneSteel Manufacturing Pty Ltd.
The goods subject of the application are hot-rolled deformed steel reinforcing bar whether or not in coil form, commonly identified as rebar or debar, in various diameters up to and including 50 millimetres, containing indentations, ribs, grooves or other deformations produced during the rolling process. The goods covered by this application include all steel reinforcing bar meeting the above description of the goods regardless of the particular grade or alloy content or
coating. The following products are excluded from the goods:
• plain round bar;
• stainless steel; and
• reinforcing mesh.
The goods are currently classified to the following tariff subheadings in schedule 3 of the Customs Tariff Act 1995.
•Tariff subheading 7214.20.00 with statistical code47;
• Tariff subheading 7228.30.90 with statistical code 49;
• Tariff subheading 7213.10.00 with statistical code 42; and
• Tariff subheading 7227.90.90 with statistical code 42.
The goods, if imported from Spain under these tariff subheadings, are subject to a general rate of duty of 5%; and the goods imported from Korea, Malaysia, Singapore, Taiwan, Thailand and Turkey are subject to a “free” rate of duty. A notice under subsection 269TD(4)(a) of the Customs Act 1901 (the Act) advising that I had made a preliminary affirmative determination was published in The Australian newspaper on 13 March 2015. In the making of that preliminary affirmative determination, I was satisfied that there appears to be sufficient grounds for the publication of a dumping duty notice in respect of the goods exported to Australia from Korea, Malaysia, Singapore, Spain, Taiwan,Thailand and Turkey. In reaching this preliminary decision, I have had regard to the requirements of section 269TAE of the Act and am satisfied that dumped goods appear to have caused material injury to the Australian industry producing like goods. The preliminary analysis of dumping margins is tabulated below. These margins were calculated under the Act by establishing export prices under subsection 269TAB(1)(a) and establishing normal values ascertained under either subsection 269TAC(1) or 269TAC(2)(c) and com paring these results in accordance with subsection 269TACB(2)(a). Margins for uncooperative exporters were calculated under 269TAB(3).
Anti dumping Austrailan market
Preliminary Affirmative Determination Report No. 264 (PAD 264) sets out the reasons for making this preliminary determination, and has been placed on the public record. Alternatively, it may be examined at the Commission’s office by contacting the Case Manager on the details provided below.
Under subsection 269TD(4)(b), I am satisfied that it is necessary to require and take securities in order to prevent material injury occurring to the Australian industry while the investigation continues. The Australian Customs and Border Protection Service will require and take securities under section 42 of the Act in respect of interim dumping duty that may become payable in respect of the goods exported from Korea, Malaysia, Singapore, Spain, Taiwan, Thailand and Turkey, entered for home consumption on or after 13 March 2015. The security that has been determined is an amount worked out in accordance with the ad valorem duty method. The securities will be imposed in relation to the goods exported to Australia from Korea, Malaysia, Singapore, Spain, Taiwan, Thailand and Turkey by all exporters at the rate specified in the above table of preliminary dumping margin assessments. Affected parties should contact the Commission by phone 132 846 or +61 2 6213 6000 (outside Australia) or at clientsupport@adcommission.gov.au for further information regarding the actual security liability calculation in their particular circumstance. I must report to the Parliamentary Secretary to Minister for Industry and Science (the Parliamentary Secretary) with final recommendations in relation to this investigation on or by 7 May 2015. The Minister will then decide whether to publish a dumping duty notice and, if relevant, the level of measures to be imposed. Further, if dumped goods give rise to retrospective notices being imposed on the goods under section 269TN of the Act, the dumping duty notice will also include the duties to be imposed retrospectively. 
Enquiries about this notice may be directed to the Case Manager on telephone number +61 3 9244 8268, fax number 1300 882 506 or +61 3 9244 8902
(outside Australia) or email at
operations3@adcommission.gov.au

Get more information at:

NAM KIM STEEL GROUP MANUFACTURER

Tel: +84650 37 9999 2 (Mr. Joshua)
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email: khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn

Thứ Sáu, 3 tháng 7, 2015

Nam Kim Steel 2nd Manufacturer Image

ENTER NAM KIM STEEL MANUFACTURE 2ND


Cold roll process line from Esmech from Germany


Cold roll process line from Esmech from Germany


Cold roll process line from Esmech from Germany

Cold roll process line from Esmech from Germany

Cold roll process line from Esmech from Germany






Nam Kim 2nd manufacturer warehouse


Slitting line process which divide the mother coil to baby coil

Galvalume process line: coating galvalume from coal roll


 Dear Sir,
Warmest greeting from Nam Kim
I am Joshua from Nam Kim Steel in Vietnam, Nam Kim Steel in Vietnam, leading a manufacturer steel coil in Vietnam such as Galvalume ( GL, PPGL ) and Galvanized ( GI, HGI and PPGL ).

We have many years experience exporting to Malaysia market, now we are exporting 1000 - 2000Mts/Month. So we understand your country policy about the SIRIM, FORM D, AP...

Which can help you import from other country with good price, and higher quality. Hopefully Nam Kim will able to support your company, and develop together.

Any questions will help us stronger in relationship, please feel free to ask me.
May I have a favor to get your inquires?

I am looking forward to hearing from you
Best regards,
Joshua


Search on Google:

Steel coil, Galvalume steel coil, Galvainzed steel coil, Steel coil sheet supply from the biggest steel in Vietnam

Galvalume steel coil Malaysia, Galvanized steel coil Indonesia, Galvalume colour steel coil USA market, Galvalume steel sheet coil Bangladesh market.

Tel: +84650 37 9999 2 (Mr. Joshua)
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email: khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn

Thứ Sáu, 8 tháng 5, 2015

AUSTRALIAN STANDARD STEEL COILS

STANDARDS AUSTRALIA

Australian standard steel sheet strip - Hot - dip zinc - coated or aluminium/zinc - coated

1. SCOPE AND GENERAL OF AUSTRALIAN STANDARD.

This standard specifies requirements for hot - dip zinc - coated or aluminium/zinc - coated seel sheet and strip, supplied in thickness up to and including 5.0 mm
Australian standard specifies requirements for steel grades, coating classes and surface finish, as follows:
 a. formability grades of steel
 b. Structual grades of steel
 c. Classes of zinc coating, including differential coating.
 d. Classes of zinc coating converted to zinc/iron alloy
 e. classes of aluminium/zinc alloy coating.
 f. Surface finish.

NOTES:
- Advice and recommendations on information to be supplied by the purchaser at the time of enquiry or order.
- Alternative means for determining compliance with this Standard are given blow
- The specified requirements apply to the full length and full width of the product supplied, unless otherwise indicated

2. SOME DEFINITIONS OF AUSTRALIAN STANDARD.

For the purpose of this Standard, the definitions below apply.
 - Wthat is the Batch
One grade of the same product form and thickness processed under similar conditions.
- What is the Coating mass
The total amount of coating on both surfaces of the steel base, measured in grams per square metre of sheet or strip. In the case of differential coatings, these surfaces are stated separately.
 NOTE: The coating thickness is not subject to specification. The approximate coating thickness for various coating classes.
 One surface single spot coating mass
The minium coating mass on any surface of any one of the three spcimens used for the triple spot test.
  Single spot coating mass
The minium coating mass on any one of the three specimens for the triple representing the original cross-section of the sheet or strip.

- What is the Coating type

  Zinc coating
Essentially a hot - dip coating of zinc incorporating minor additions of control elements only ( Type Z ) or a coating of zinc converted to a zinc/iron alloy ( Type ZF )
  NOTE: A type Z coating normally provided with a chromate passivation treatment, not oiled, Atype ZF coating is normally lightly phosphted, or oiled

   Aluminium/Zinc alloy coating

A hot - dip coating compossed of essentially 50% to 60% aluminium with the remaninder zinc but incorporating minor additions of control elements. ( type AZ )
  NOTE: A type AZ coating is normally provided with a chromate passivation treatment in conjuction with a thin clear organic coating, not olied

- What is the differential coating

A coating which has a substantially different coating mass on each side of the steel sheet or strip.
  Sheet
a flat rooled product of any width and thickness coated by hot dipping and suppled in cut lengths
Trip
A flat rolled product of any width and thickness coated by hot dipping and supplied in coil form.


Get more information at:NAM KIM STEEL GROUP MANUFACTURER
Tel: +84650 37 9999 2 (Mr. Joshua)
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email: khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn

Search on Google:

Galvalume steel coil (GL)

Galvanized steel coil (GI)

Galvalume and Galvanized colour (PPGI, PPGL )

aluminium - zinc alloy coated steel (GL )

USA, American, Houston port, new orleans, tampa, philadelphia, sanfrancisco port, stockton, camden, baltimore, altamira (Altamira), vercuaz ( Mexico )










































































Thứ Bảy, 25 tháng 4, 2015

Standard Specification for Steel Coil, 55 % Aluminum-Zinc Alloy-Coated by the HotDip Process

Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the HotDip Process



1. Classification of Aluminum - zinc Alloy - Coated by the Hot Dip process (Galvalume - GL)

The material is available in several designations, as follows:
- Commercial Steel—CS Types A, B, and C,
- Forming Steel—FS,
- Drawing Steel—DS,
- High Temperature Steel—HTS, and
- Structural Steel—SS.

Structural steel is available in several grades based on mechanical properties. Structural Steel Grade 50 [340] is available in three classes based on tensile strength. Structural Steel Grade 80 [550] is available in two classes, based on chemistry. The product is available in several coating weights
[masses] with the coating designation in accordance with this table


 2. Mechanical Properties of Aluminum - zinc Alloy - Coated by the Hot Dip process (Galvalume - GL)



Many interrelated factors that affect the ability of a steel to cold form over a given radius under shop conditions. These factors include thickness, strength level, degree of restraint, relationship to rolling direction, chemistry, and base metal microstructure. Lists the suggested minimum inside radii for 90° cold bending for Structural Steels. They presuppose “hard way” bending (bend axis parallel to the rolling direction) and reasonably good shop forming practices. Where possible, the use of larger radii or “easy way” bends are recommended for improved performance.
Fabricators should be aware that cracks may initiate upon bending a sheared or cold-worked edge. This is not considered to be a fault of the steel but is rather a function of the induced localized cold-work zone.
 
Joshua
Tel: +84650 37 9999 2
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email:
khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn

Search on Google:

Galvalume steel coil (GL)

Galvanized steel coil (GI)

Galvalume and Galvanized colour (PPGI, PPGL )

Aluminium - zinc alloy coated steel (GL )

USA, American, Houston port, new orleans, tampa, philadelphia, sanfrancisco port, stockton, camden, baltimore, altamira (Altamira), vercuaz ( Mexico )




Thứ Ba, 31 tháng 3, 2015

PREPAINTED GALVALUME

PREPAINTED GALVALUME Coil

  • Spec: JIS G3322
  • Thickness range : 0.20 ~ 0.80mm
  • Width: 760~1250 mm
  • Top coating side: 15~30 ±1 µm (including one primer layer and one complete layer of polyester paint)
  • Back coating side: 5~20 ±1 µm (including one primer layer and one complete layer paint)
  • Hardness of pencil: HB ~ 3H
  • Durability of solvent: MEK ≥ 100DR
Our products produced on the NOF technology (Non Oxidizing Furnace) - A kind of the steel annealing furnace without oxygen of the most advanced technology in the world. Therefore, they have dominant characteristics as follow:
- Designed to paint two identical layers on the two sides of the products
- Especially designed and produced to severe weather conditions
- Better corrosion resistance
- Durability

- Diversified colors

NAM KIM Steel JSC is one of leading steel manufacturer in Vietnam
Our main markets are Southeast Asia, Middle East, South Asia, Indonesia, Singapore, Myanmar, Philippine, Japan, Korea, etc.

Our  products have certificated by many standards: ISO (ISO 9001: 2000, ISO 14001: 2004), JIS (Japan Industrial Standard) JIS G3341, G3322, G3321,G3312, G3302, USA (ASTM A792/792M), Australia (AS 1397(G550), AS 1365(G300)...

There are our several products as follows:
+ (GI); (GL);(PPGI);(PPGL) prime and secondary
+ Steel pipe & tube ( black, galvanized, stainless), purlin, flat steel sheet

At the moment, we have two factory which is located on Binh Duong Province with the best production lines. And our products is always chosen very strick before packing and exporting .
If you have any interest in our products, please don't hesitate to contact and give us your mail address, we will send you quotation of those items. I assure you that we can supply good quality products at very competitive prices.
Hopefully, the two companies will enjoy a good association in the future.

Get more information at:
NAM KIM STEEL GROUP MANUFACTURER
Tel: +84650 37 9999 2 (Mr. Joshua)
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email: khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn

Thứ Năm, 19 tháng 3, 2015

HOT DIP 55% ALUMINIUM - ZINC ALLOY COATED STEEL

HOT DIP 55% ALUMINIUM - ZINC ALLOY COATED STEEL


ALUMINIUM - ZINC ALLOY COATING LINE ( NOF TECNOLOGY )

Technology
NOF ( Non-Oxidising Furnance )
Capacity
150,000 ( MTs/year)
Total coating thickness
0.22 - 1.2 (mm)
Width
750 - 1,1250 (mm)
Coil weight
Max 25,000 (kg)
Inner Dia
508/610 (mm)
Outer Dia
Max 2,200 (mm)


Technology: NOF
Standard: JIS 3321/ ASTM A792
Coating thickness: AZ50 - AZ 210 (*)
Base Metal Thickness: 0.20 - 1.0 (mm)
Width: 600 - 1,250 (mm)
(*) AZ is used for the aluminium-zinc coated layer
Outstanding quality:
Especially produced for various using purpose. Duration is 4 times longer than other normail Gls. High anti-corrosion and anti-heat
The anti-finger layer:
Anti-stain and anti-oxidization. Keeping the surface of the products shiny for a long time. Reduce cracks, scratchs of coating layer in the process of stamping and rolling.

Applications:
Industrial & civil construction.
Production of roofing, walls, ceilings, gutters...
Sliding door, rolling door, folding door..
Interior and exterior decoration.
Drainage pipes, air conditioning pipes.
Computer cases, electrical cabinets, washing machines...

Nam Kim Steel Company 

Search on Google:

Steel coil, Galvalume steel coil, Galvainzed steel coil, Steel coil sheet supply from the biggest steel in Vietnam

Galvalume steel coil Malaysia, Galvanized steel coil Indonesia, Galvalume colour steel coil USA market, Galvalume steel sheet coil Bangladesh market.

Tel: +84650 37 9999 2 (Mr. Joshua)
Mobile/Viber/Whatsapp: +84 169.949.3.696
Skype: thaiphikhanh_bily
Email: khanhtp@namkimgroup.vn
Webiste: www.namkimgroup.vn